LP150X08 TL A2 PDF

Philips LCD LPXTLA2 datasheets download: a-Si TFT-LCD, “, × , nit, (Typ.), K, 60Hz, CCFL, LVDS (1 ch. Find great deals for LG Philips LPX08 TL A2 15” Laptop LCD Screen. Shop with confidence on eBay!. *When you obtain standard approval, please use the above model name without suffix. LPX *MODEL. TLA2. Suffix. s LCD Co.

Author: Mijin Malazil
Country: Somalia
Language: English (Spanish)
Genre: Video
Published (Last): 23 February 2015
Pages: 126
PDF File Size: 7.62 Mb
ePub File Size: 13.18 Mb
ISBN: 322-8-88860-543-9
Downloads: 74036
Price: Free* [*Free Regsitration Required]
Uploader: Gokazahn

LG Philips LP150X08 TL A2 15″ Laptop LCD Screen

Mark,Reliability Environment test condition No. In lower temperature, it becomes lower. In addition the figures in the next page are detailed mechanical drawing of the LCD. All VCC power input pins should be connected together. Active Area 9 1 10 4 11 12 5 13 FIG. Please avoid floating state of interface signal at invalid period.

The inverter is an external unit to the LCD. The output of the inverter must have symmetrical negative and positive voltage waveform and symmetrical current waveform.

Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers.

Search the history of over billion web pages on the Internet. The lamp power consumption shown above does not include loss of external inverter.

And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly pl150x08 the module. Condensation makes damage to polarizer or electrical contacted parts. The used lamp current is the lamp typical current.

  JUDO GOKYO PDF

LPXTLA2[1]_图文_百度文库

Viewing angle is the angle at which the contrast ratio is greater than Viewing angle is the angle at which the contrast ratio is greater than And after fading condensation, smear or spot will occur. Make certain that treatment persons are connected to ground through wrist band etc. Usually ships the same day you order, based on lp15008 the order is placed. For more information see FIG 1.

Twisted stress is not applied to the module. For more information see FIG 1. When the glue remains on the bezel surface lp1150x08 its vestige pl150x08 recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.

In combination with the vertical arrangement of the sub-pixels, the LPX08 characteristics provide an excellent flat display for office automation products such as Notebook PC.

Lamp power must be turn on after power supply for LCD and interface signal are valid. Please contact us should you have any questions regarding Acer laptop screens, as our knowledgeable sales staff are laptop screen product specialists.

The lamp power consumption shown above does not include loss of external inverter. In lower temperature, it lp150x088 longer. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following.

LPXTLA2 s LCD Co., Ltd. |

For more information see FIG 2. The design of the inverter must have specifications for the lamp in LCD Assembly. The label is attached to the backside of the LCD module. The pin configuration for the connector is shown in the table below. Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more thancolors.

  GORSKI VIJENAC PETAR PETROVIC NJEGOS PDF

Please shop with caution! We have simple, step-by-step instructions to remove the LCD screen from your laptop. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module.

And in lower temperature, response time required time that brightness is stable after turned on becomes 2a. Do not expose the module to sunlight or fluorescent light.

Because leakage current is occurred between lamp wire and conducting tape. Transparent protective plate should have sufficient strength in order to the resist external force. When you confirm it, the LCD— Assembly should be operated in the same condition as installed in you instrument. This LCD employs two interface connections, a 30 pin connector is used for the module electronics and the other connector is used for the integral backlight system.

Do not expose the module to sunlight or fluorescent light. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. Our competitors sell “refurbished” screens when in fact their screens are used or non-refurbished. Temperature and relative humidity range are shown in the figure below.

Grounding and shielding methods may be important to minimized the interference.